Cabinet Dehumidifiers
Intelligent Cabinet Dehumidifier

Model: Intelligent Cabinet Dehumidifier

Thermoelectric dehumidifier for electrical cabinets and switchgear, with adjustable humidity control, condensate drainage, defrosting and RS485 communication.

Technical Specifications

Product typeIntelligent thermoelectric cabinet dehumidifier / anti-condensation device
Power supplyAC/DC 220 V
Dehumidification power options30 W, 45 W or 60 W
Dehumidification rate450 mL/day for the 60 W version at 35 °C and 80% RH
Humidity measurement range5–95% RH; accuracy ±5% RH
Temperature measurement range−20 to 60 °C; accuracy ±1 °C
External heating power range50–500 W; heating output or alarm output must be selected
Communication interfaceRS485; confirm the communication protocol for the selected version
Control outputDry contact, configured for external heating or alarm
Drain tubeSilicone, diameter 8 mm, length 1 m
Mounting35 mm rail mounting; confirm the outline and mounting arrangement for the selected version

Key Features

Applications

Electrical switchgear cabinetsElectrical enclosures in humid locationsCabinet anti-condensation and moisture management

Product Description

Intelligent Cabinet Dehumidifier

This smart anti-condensation device uses semiconductor thermoelectric cooling to remove moisture from the air inside enclosed electrical cabinets. A fan draws humid air across the cooling element, water vapour condenses, and the collected water drains outside the cabinet through a tube. It is intended for managing moisture and condensation inside switchgear and similar electrical enclosures.

Functions and Operation

  • Thermoelectric condensation removes moisture from the air inside an electrical cabinet
  • Condensate is discharged outside the cabinet through a drain tube
  • Adjustable humidity start/stop thresholds and temperature-control settings
  • Automatic defrosting when frost forms on the cooling element
  • High-humidity warning, fault-code display and status indication
  • RS485 communication interface; select either the external-heating output or the alarm output

The humidity load starts when humidity rises above Ho1 and stops when it falls below Ho2, with Ho1 set higher than Ho2. For external-heater control, heating starts below Co1 and stops above Co2, with Co1 set lower than Co2. The heating function controls an external heater.

If humidity has not fallen to the configured operating threshold after 10 hours, the fault indicator flashes. Review the moisture load and dehumidification capacity for the installation. Fault codes and a fault indicator help identify power, fan or dehumidification-system faults.

Applications

  • Moisture and condensation management inside electrical switchgear.
  • Electrical cabinets in humid locations, including basement installations.
  • Cabinets exposed to temperature changes or extended periods out of service.

Technical Specifications

ParameterSpecification
Product typeIntelligent thermoelectric cabinet dehumidifier / anti-condensation device
Power supplyAC/DC 220 V
Dehumidification power options30 W, 45 W or 60 W
Dehumidification rate450 mL/day for the 60 W version at 35 °C and 80% RH
Humidity measurement range5–95% RH; accuracy ±5% RH
Temperature measurement range−20 to 60 °C; accuracy ±1 °C
External heating power range50–500 W; heating output or alarm output must be selected
Communication interfaceRS485; confirm the communication protocol for the selected version
Control outputDry contact, configured for external heating or alarm
Drain tubeSilicone, diameter 8 mm, length 1 m
Mounting35 mm rail mounting; confirm the outline and mounting arrangement for the selected version

The 450 mL/day figure applies to the stated 60 W test condition. Actual water removal depends on cabinet temperature, humidity and moisture ingress; it is not a capacity claim for every environment or power option.

Control Settings

CodeFunctionFactory setting
Ho1Humidity ON85% RH
Ho2Humidity OFF75% RH
Co1Temperature ON5 °C
Co2Temperature OFF15 °C
dHHumidity offset0
AddDevice address01

The factory mode combines dehumidification with heating control. Select either the external-heating output or the alarm output; these are alternative uses of the output. Set the humidity and temperature thresholds to suit the cabinet and connected equipment.

Installation and Configuration

The rail-mounted arrangement uses a standard 35 mm rail fixed to the panel. Keep the air outlet clear and route the condensate drain outside the cabinet. Obtain the outline drawing and terminal diagram for the selected version before cabinet design or wiring.

The RS485 interface supports transmission of temperature, humidity, settings and fault information. Confirm the communication protocol and terminal arrangement for the ordered version before integration.

Ordering Information

Please specify the required product configuration when requesting a quotation:

  1. Required model or version and quantity.
  2. Dehumidification power: 30 W, 45 W or 60 W.
  3. Supply requirements and selection of external-heating control or alarm output.
  4. Cabinet dimensions, installation space, temperature and humidity conditions, and drain routing.
  5. RS485 integration requirements and the required outline and terminal drawings.

Request a cabinet dehumidifier quotation

Related Products